Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fa8000
****************************
Init GPIO Pin****************************
flash_protect ON: from 0xBFC00000 to 0xBFC262B7
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF
protect on 10
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
DRAM COMPONENT: 256Mbits
DRAM BUS: 16BIT
Total memory: 32 MBytes
Flash: 4 MBytes
Date:Apr 16 2009 Time:10:03:22
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 320 MHZ ####
SDRAM bus set to 16 bit
SDRAM size =32 Mbytes
Please choose the operation:
0: Load ucos code to SDRAM via TFTP Client.
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
0: System Load Boot Loader | F/W then write to Flash via TFTP Client.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) Input server IP (10.10.10.3) Input Li
nux Kernel filename (<NULL>)
Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fa8000
****************************
Init GPIO Pin****************************
flash_protect ON: from 0xBFC00000 to 0xBFC262B7
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
protect on 9
flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF
protect on 10
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
DRAM COMPONENT: 256Mbits
DRAM BUS: 16BIT
Total memory: 32 MBytes
Flash: 4 MBytes
Date:Apr 16 2009 Time:10:03:22
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 320 MHZ ####
SDRAM bus set to 16 bit
SDRAM size =32 Mbytes
Please choose the operation:
0: Load ucos code to SDRAM via TFTP Client.
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bfc50000 ...
Bad Magic Number,43535953
Image Name: Linux Kernel Image
Created: 2009-11-03 9:38:24 UTC
System Control Status = 0x20400000
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3653548 Bytes = 3.5 MB
Load Address: 80000000
Entry Point: 802bc000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 802bc000) ...
## Giving linux memsize in MB, 32
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.21 (root@vance.localdomain) (gcc version 3.4.2) #142 Tue Nov 3
17:30:33 CST 2009
The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 80800034, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 00138800(1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29468k/32768k available (2266k kernel code, 3300k reserved, 529k data, 1
16k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB
***********Init LED Driver*****************
Init GPIO Pin
Init GPIO Direction
Init GPIO Interrupt
***********Init LED Driver Finishing*****************
Ralink_gpio_init_irq
LED & GPIO & LAN Status Driver LED_VERSION
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocat
ed, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
mtd: Giving out device 0 to Bootloader
0x00030000-0x00040000 : "Config "
mtd: Giving out device 1 to Config
0x00040000-0x00050000 : "Factory"
mtd: Giving out device 2 to Factory
0x00050000-0x00160000 : "Kernel"
mtd: Giving out device 3 to Kernel
0x00160000-0x003e0000 : "RootFS"
mtd: Giving out device 4 to RootFS
0x003e0000-0x00400000 : "Cimage"
mtd: Giving out device 5 to Cimage
0x00050000-0x003e0000 : "Uimage"
mtd: Giving out device 6 to Uimage
block2mtd: version $Revision: 1.1.1.1 $
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Using DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 2.6.21 dwc_otg_hcd
usb usb1: SerialNumber: lm0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
u32 classifier
Performance counters on
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
ipt_time loading
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.11.1 (2009-11-03 17:37:25 CST)
starting pid 606, tty '': '/etc/rc.sh'
Cannot run '/etc/rc.sh': No such file or directory
BusyBox v1.11.1 (2009-11-03 17:37:25 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
Sat Jan 1 00:00:00 UTC 2000
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
killall: failover.sh: no process killed
ifconfig: 0.0.0.0: error fetching interface information: Device not found
phy_rx_ring = 0x01cdc000, rx_ring = 0xa1cdc000, size: 16 bytes
GDMA1_FWD_CFG = 710000
eth2.1: Setting MAC address to 00 1f 1f 6d 80 fc.
VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious
mode.
eth2.2: Setting MAC address to 00 0f ea c4 35 3c.
device eth2 entered promiscuous mode
VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
Initialize WLAN interface
Setup BRIDGE interface
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
ifconfig: ioctl 0x8913 failed: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth2.1 entered promiscuous mode
eth2.1: dev_set_promiscuity(master, 1)
route: ioctl 0x890c failed: No such process
br0: port 1(eth2.1) entering learning state
br0: topology change detected, propagating
br0: port 1(eth2.1) entering forwarding state
route: ioctl 0x890c failed: No such process
route: ioctl 0x890c failed: No such process
Static DHCP Leases disable!
route: ioctl 0x890c failed: No such process
device eth2 is not a slave of br0
device eth2.1 is already a member of a bridge; can't enslave it to bridge br0.
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
Set: phy[0].reg[0] = b100
Set: phy[1].reg[0] = b100
Set: phy[2].reg[0] = b100
Set: phy[3].reg[0] = b100
Set: phy[4].reg[0] = b100
**********************************************************************
* Running Diagd *
**********************************************************************
**********************************************************************
* Enable WSC_UPnP *
**********************************************************************
/bin/init.sh: line 522: wscd: not found
**********************************************************************
* Enable LLTD *
**********************************************************************
killall: snmpd: no process killed
killall: lld2d: no process killed
**********************************************************************
* Enable GPIO Interrupt *
**********************************************************************
ralink_gpio:ioctl GPIO REG
ralink_gpio:ioctl GPIO REG
killall: watchdog.sh: no process killed
ip_table: set wan_name=eth2.2
killall: radiusd: no process killed
RADIUS server disable !!
kill: you need to specify whom to kill
**********************************************************************
* FREE Page,Dentries and Inodes Cache *
**********************************************************************
MemFree: 23608 kB
Cached: 1340 kB
killall: pppd: no process killed
killall: pptp.sh: no process killed
killall: pppoe.sh: no process killed
ifconfig: 0.0.0.0: error fetching interface information: Device not found
Setup WAN interface
ifconfig: 0.0.0.0: error fetching interface information: Device not found
device eth2 is not a slave of br0
device eth2.1 is already a member of a bridge; can't enslave it to bridge br0.
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
Set: phy[0].reg[0] = b100
Set: phy[1].reg[0] = b100
Set: phy[2].reg[0] = b100
Set: phy[3].reg[0] = b100
Set: phy[4].reg[0] = b100
udhcpc (v1.11.1) started
rm: cannot remove '/tmp/agentenabledflag': No such file or directory
/bin/start_wan.sh: line 265: /bin/agent: nip_table: set wan_name=eth2.2
ot found
killall: modemctl: no process killed
ralink_gpio:ioctl GPIO REG
ralink_gpio:ioctl GPIO REG
into eth2.2.deconfig
so manybe the whr.g300bui9ld will run. try to install it via serial
I destroyed RX pad on PCB, serial flash is not an option for my.
Only TX is working, I can only listen.
Can I do this by Eternet, it involves a greater risk?
If you hold down at startup reset the router is switched on at ip192.168.1.6 and waiting for the tftp.
Can I do this by Eternet, it involves a greater risk?
If you hold down at startup reset the router is switched on at ip192.168.1.6 and waiting for the tftp.
